Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Just Stopped
#1
My CO2 monitor has just stopped sending data via MQTT.  I have not done anything.  LED is purple.  Tried connecting it to th Chrome app and all seems fine. Tried an otah command but still nothing.

Startup log.

Searching for v.Air Trying : COM1

Trying : COM6

 .  . [ŽHAÙ4`M,à…ð`8€ðú]
[þ]
 . [Heap Heap at start: 32384

vES]
[Prino v1.16 build20161230
IP ad]

vESPrino found on : COM6
[No I2C Devices found

--- Setup PLUGINS ---
Neopixel
nop 0
ready >
DweetIO
WebServer
WebSocketServer
PowerManager
GPIO
Servo
Annemometer
TimerManager

--- Setup SENSORS ---
CO2
TEST
SI7021
BME280
BMP085
PM2005
CDM7160
DS18B20
TSL2561
BH1750
APDS9960

--- Setup DESTINATIONS ---
CustomHTTP
SerialDump
MQTT
RFX10
Blynk
Heap At setup end: 30176
sendNowCond

--- DestHanlder: sendValue --- 1
CustomHTTPDest::process
SerialDumpDest::process
IP    : 0.0.0.0
CHIPID    : 147B8A
RUNTIME    : 3
MQTTDest::process
Waiting for WiFi]
[]
[.]
[.]
[IP address: 192.168.7.xxx in 6457 ms
GOT IP

Sending via MQTT: 192.168.7.xx,1883
Connecting to server :vESPrino,,
MQTT Connected
RFDest::process
info

vESPrino v1.16 build20161230
IP address: 192.168.7.x]
[08
Chip ID: 147B8A
ready >]
[crc40prop_list
prop_list
---vESPrinoCFG_start---
isMigrated=1
rf.CO2=136
rf.PM25=137
rf.PM10=138
rf.TEMP=140
rf.HUM=141
rf.PRES=142
rf.GEN=143
send.interval=120
wifi.ssid=xxxxxx
wifi.p1=xxxxxxxx
cubic.co2.missing=missing
ds18b20.port=missing
mqtt.server=192.168.7.xx
mqtt.port=1883
mqtt_msg_arr0=rx/22:{"CO2-2":%CO2%}
---vESPrinoCFG_end---
ready >]
[sendNowCond

--- DestHanlder: s]
[endValue --- 0
ready >]
Reply
#2
can you enable debug, and send me some logs, what happens after you try sending a test message( with the Test button)
Reply
#3
(01-02-2017, 12:51 PM)admin Wrote: can you enable debug, and send me some logs, what happens after you try sending a test message( with the Test button)

Test button output. I note the MQTT says failed but I see the connection to the broker at the other end.


[Scheduling command: crc4AsendNow
Scheduling command: nop
crc4AsendNow
Scheduling command: sendNow
PowerManager timeout: 0
PowerManager disabled
sendNow

--- DestHanlder: sendValue --- 1
CustomHTTPDest::process
SerialDumpDest::process
IP    : 192.168.7.xxx
CHIPID    : 147B8A
RUNTIME    : 119
MQTTDest::process
Sending via MQTT: 192.168.7.xx,1883
Connecting to server :vESPrino,,
MQTT Connected
Failed!
RFDest::process
Heap : 29464
ready >]
Reply
#4
Can you send me the output from the begin
Right after you connect to it
Looks like it does not find the sensors over i2c

Which was your version?
Reply
#5
(01-02-2017, 05:16 PM)admin Wrote: Can you send me the output from the begin
Right after  you connect to it
Looks like it does not  find the sensors over i2c

Which  was your version?

Log sent by PM

Version CM1102
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)