Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
RF Connectivity
#4
Aahh great, yeah - the RF section is currently the only thing left with high prio on my backlog and i was planning to give it a go this week.
Each RFXMeter message is sent with an ID - you can configure the IDs in the Config Tool.
For the "GEN" field (143 by default) you can remove the ID from there - this is the ID where the device sends some values that some sensors report but are not configured yet. And i recently started pushing some values for IP and UPTIME, which may be the ones that you do not recognize

For the other values - CO2, TEMP, Pressure - the value is multiplied by 100 and then sent as an integer.

This is the current state.

Couple of months back i had a discussion with Bert from rfxcom on integrating the device there. What we agreed is that i will start using
RFXSensor for temperature, pressure and humidity
and RFXMeter for Dust, CO2 and High Precision temperature (RFXSensor is only 0.5 degree precision)
Quote:Good idea to use the RFXSensor protocol for temp, hum and baro because it does not need any adaptation in the applications and RFXtrx.
 
I think you can use the RFXMeter as it is because at this moment the type of metering (power, gas, water) is selected in the applications. This could also be done for your CO2 and dust measuring. And high precision temp is also possible. 
I propose not to change anything.
So in domoticZ you would need to select for the corresponding IDs what they are and mutiply them accordingly

What is strange is why you do not get the Temperature reading, is there an ID for the TEMP ?
Reply


Messages In This Thread
RF Connectivity - by admin - 09-22-2016, 04:32 AM
RE: RF Connectivity - by nmaster - 12-09-2016, 04:43 PM
RE: RF Connectivity - by nmaster - 12-09-2016, 05:59 PM
RE: RF Connectivity - by admin - 12-10-2016, 04:07 AM
RE: RF Connectivity - by nmaster - 12-10-2016, 11:11 AM
RE: RF Connectivity - by vaanja - 12-10-2016, 12:48 PM
RE: RF Connectivity - by nmaster - 12-10-2016, 01:20 PM
RE: RF Connectivity - by admin - 12-11-2016, 04:12 AM
RE: RF Connectivity - by nmaster - 12-11-2016, 11:30 AM
RE: RF Connectivity - by nethenic - 01-11-2017, 04:43 PM
RE: RF Connectivity - by admin - 01-12-2017, 06:45 AM
RE: RF Connectivity - by nethenic - 01-12-2017, 09:00 PM
RE: RF Connectivity - by admin - 01-13-2017, 06:21 AM
RE: RF Connectivity - by wokkelp - 02-15-2017, 04:55 PM
RE: RF Connectivity - by admin - 02-16-2017, 03:18 AM
RE: RF Connectivity - by wokkelp - 02-16-2017, 10:22 AM
RE: RF Connectivity - by admin - 02-16-2017, 12:07 PM
RE: RF Connectivity - by wokkelp - 02-16-2017, 03:45 PM
RE: RF Connectivity - by admin - 02-16-2017, 06:02 PM
RE: RF Connectivity - by vbs - 02-25-2017, 09:33 PM
RE: RF Connectivity - by admin - 02-26-2017, 08:28 AM
RE: RF Connectivity - by vbs - 02-26-2017, 10:25 AM
RE: RF Connectivity - by admin - 02-26-2017, 12:05 PM
RE: RF Connectivity - by vbs - 02-26-2017, 03:36 PM
RE: RF Connectivity - by admin - 02-27-2017, 01:56 PM
RE: RF Connectivity - by vbs - 02-27-2017, 04:00 PM
RE: RF Connectivity - by admin - 02-28-2017, 03:37 AM
RE: RF Connectivity - by vbs - 03-02-2017, 10:25 PM
RE: RF Connectivity - by Christopher Wansing - 04-19-2017, 05:04 PM
RE: RF Connectivity - by admin - 03-03-2017, 03:57 AM
RE: RF Connectivity - by vbs - 04-19-2017, 07:32 PM
RE: RF Connectivity - by Christopher Wansing - 04-19-2017, 07:53 PM
RE: RF Connectivity - by vbs - 04-19-2017, 08:50 PM
RE: RF Connectivity - by admin - 05-05-2017, 02:24 AM
RE: RF Connectivity - by vbs - 05-05-2017, 06:21 AM

Forum Jump:


Users browsing this thread: 3 Guest(s)