Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
New Functionalities in Build 2017.02.19
#7
Here the result, in debug mode :

Code:
Scheduling command: @nop
crc26##prop_jset"stored.i2c"##prop_jset"cubic.co2.missing"##prop_jset"ds18b20.port"##prop_jset"has.sensors"##restart##
Scheduling command: ##prop_jset"stored.i2c"##prop_jset"cubic.co2.missing"##prop_jset"ds18b20.port"##prop_jset"has.sensors"##restart##
##prop_jset"stored.i2c"##prop_jset"cubic.co2.missing"##prop_jset"ds18b20.port"##prop_jset"has.sensors"##restart##
Scheduling command: prop_jset"stored.i2c"
Scheduling command: prop_jset"cubic.co2.missing"
Scheduling command: prop_jset"ds18b20.port"
Scheduling command: prop_jset"has.sensors"
Scheduling command: restart
prop_jset"stored.i2c"]
[prop_jset"cubic.co2.missing"]
[prop_jset"ds18b20.port"]
[prop_jset"has.sensors"]
[restart
wss_stop]
[¥„\ÔEŽŒ:¥ÿþ]
[DEBUG is: 1LED SetColor:  seq1l
LED AutoBrg: 0.99]
[LED SetColor:  seq1lnlnd
LED AutoBrg: 0.99]
[vESPrino v1.16 build20170219
IP address: 0.0.0.0
Chip ID: CFC49D]
[Found i2c bus on SDA:SCL = D5:D1 (14:5)]
[Using I2C Bus on SDA:SCA (14:5)
i2c bus storing: 0x050E]
[--- Setup PLUGINS ---
WifiStuff
WebSocketServer
PowerManager]
[Neopixel
No Name
DweetIO
WebServer]
[PowerManager
GPIO
Annemometer
DestinationManager
TimerManager

--- Setup SENSORS ---]
[CM110x : 0
Turning on CM110x Sensor]
[Trying : 12,13
Getting CO2 Sensor Software Version]
[E8,FF,FE,3F,88,FF,FE,3F,54,2F,FF,3F,2E,54,20,40,14,95,FE,3F,88,FF,FE,3F,
Trying : 13,12
Gettin]
[g CO2 Sensor Software Version
E8,FF,FE,3F,8A,FF,FE,3F,54,2F,FF,3F,2E,54,20,40,14,95,FE,3F,8A,FF,FE,3F,
+]
[Trying : 12,13
Getting CO2 Sensor Software Version]
[E8,FF,FE,3F,88,FF,FE,3F,54,2F,FF,3F,2E,54,20,40,14,95,FE,3F,88,FF,FE,3F,
Trying : 13,12
Gettin]
[g CO2 Sensor Software Version
E8,FF,FE,3F,8A,FF,FE,3F,54,2F,FF,3F,2E,54,20,40,14,95,FE,3F,8A,FF,FE,3F,
+]
[Trying : 12,13
Getting CO2 Sensor Software Version]
[E8,FF,FE,3F,88,FF,FE,3F,54,2F,FF,3F,2E,54,20,40,14,95,FE,3F,88,FF,FE,3F,
Trying : 13,12
Gettin]
[g CO2 Sensor Software Version
E8,FF,FE,3F,8A,FF,FE,3F,54,2F,FF,3F,2E,54,20,40,14,95,FE,3F,8A,FF,FE,3F,
+]
[ERROR: Could not locate Cubic CO2 Sensor]
[IP address: x.x.x.x in 10942 ms
GOT IP
LED SetColor:  seqcncncnd]
[Scheduling command: wss_start
wss_start


WebSockets Server started on wss://x.x.x.x:8266
Open http://config.vair-monitor.com to configure device online]
[ready >
SI7021 : 0
Found: SI7021
TEST : 0
BME280 : 0]
[BMP085 : 0]
[PM2005 : 0]
[CDM7160 : 0]
[DS18B20 : 0
DS18B20: searching on port: D1]
[DS18B20: searching on port: D5]
[DS18B20: searching on port: D6
DS18B20: searching on port: D7]
[DS18B20 is on: missing
LDR : 0
Found: LDR
TSL2561 : 0]
[BH1750 : 0]
[APDS9960 : 0]
[Found Sensors: SI7021,LDR,


--- Setup DESTINATIONS ---
CustomHTTP
SerialDump
MQTT]
[RFX10
Blynk
RGBLed]
[Heap At setup end: 30400
Device initialized.
Scheduling command: @sendNow
Check time from google]
[SI7021 : 78ms
LDR : 0ms


Should I try to open the box to check it ? It seems that the CDM7160 stay unavailable ..

Thanks,
Reply


Messages In This Thread
RE: New Functionalities in Build 2017.02.19 - by jasp - 02-19-2017, 09:20 AM

Forum Jump:


Users browsing this thread: 1 Guest(s)