Help getting started

[ESteg]

Received my 2 monitors yesterday (shipping to the Netherlands). After connecting the monitor that's based on the 1102 sensor, I could update the WiFi settings and the latest firmware was automatically updated. Very smooth! I did have some issues though getting the monitor to update values to ThingSpeak.

When I tried the other monitor, with the 7160 sensor (+ temp/hum/press), it immediately started to update all 4 values to ThingSpeak (with a different API, of course).

Here's a dump of the output after connecting the 1102 monitor: I'm not an expert on this, do you notice anything that explains why this monitor won't show the "Raw CO2" values like the 7160 monitor?

Many thanks!
Etienne

Code:

Searching for v.Air Trying : COM7

.  . [È$l]
[,4ð]
[¤$r[ùxIÒ]
[ú]
[…]
[Heap Heap at start: 34872]
[No I2C Devices found

vESPrino]

vESPrino found on : COM7
[OK
ready >]
[OK

vESPrino v1.16 build20160925]
[IP address: 0.0.0.0
Chip ID: CFC413]
[ready >.]
[OK
---vESPrinoCFG_start---
isMigrated=1
rf.CO2=136
rf.PM25=137
rf.PM10=138
rf.TEMP=140
rf.HUM=141
rf.PRES=142
rf.GEN=143
send.interval=120
wifi.ssid=[SSID that I entered]
wifi.p1=[password]
tsKey=[thingspeak API]
custom_url_arr0=#http://api.thingspeak.com/update?key=[Correct API]&field1=%CO2%
---vESPrinoCFG_end---
ready >]
[.]
[.

--- Setup PLUGINS ---
Setup plugin: Neopixel
Setup plugin: TimerManager

--- Setup SENSORS ---
Setup sensor: TEST
Setup sensor: CO2]
[CO2 Sensor SW Ver: BS V3.029 0i
CM1102 Dual Beam NDIR sensor
CO2 now: 550
Setup sensor: SI7021
Setup sensor: BME280
Setup sensor: PM2005
Setup sensor: CDM7160

--- Setup DESTINATIONS ---
Setup Destination: CustomHTTP
Setup Destination: SerialDump
Setup Destination: MQTT
Setup Destination: RFX10
Heap At setup end: 32144
Waiting for WiFi ready >.]
[.]
[.]
[.]
[IP address: 192.168.xxx.xxx in 13306 ms
GOT IP]
[fg: 20160925, fc: 0, bn:20160925
ready >
--- DestHanlder: sendValue ---]
[CustomHTTPDest::process
CustomHTTPDest::invoke = http://api.thingspeak.com/update?key=[Correct API]&field1=%CO2%]
[Response Code: 500
CLOSED]
[SerialDumpDest::process
MQTTDest::process
RFDest::process
ready >]
[--- DestHanlder: sendValue ---]
[--- DestHanlder: sendValue ---]
[--- DestHanlder: sendValue ---]
[OK
ready >]
[--- DestHanlder: sendValue ---]
[--- DestHanlder: sendValue ---]
[--- DestHanlder: sendValue ---]
[--- DestHanlder: sendValue ---]
[OK
ready >]
[--- DestHanlder: sendValue ---]
[CustomHTTPDest::process
CustomHTTPDest::invoke = http://api.thingspeak.com/update?key=[Correct API]&field1=860.00]
[Response Code: 200
CLOSED]
[SerialDumpDest::process
CO2    : 860.00
MQTTDest::process
RFDest::process
ready >]
[--- DestHanlder: sendValue ---]
[ready >]
[--- DestHanlder: sendValue ---]
[--- DestHanlder: sendValue ---]
[OK
ready >]
[--- DestHanlder: sendValue ---]
[--- DestHanlder: sendValue ---]
[--- DestHanlder: sendValue ---]
[--- DestHanlder: sendValue ---]
[OK
ready >]
[--- DestHanlder: sendValue ---]
[CustomHTTPDest::process
CustomHTTPDest::invoke = http://api.thingspeak.com/update?key=[Correct API]&field1=860.00]
[Response Code: 200
CLOSED]
[SerialDumpDest::process
CO2    : 860.00
MQTTDest::process
RFDest::process]
[--- DestHanlder: sendValue ---]
[--- DestHanlder: sendValue ---]
[OK
ready >]
[--- DestHanlder: sendValue ---]
[--- DestHanlder: sendValue ---]
[--- DestHanlder: sendValue ---]
[--- DestHanlder: sendValue ---]