Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
[SOLVED] No values are send to any of my services.
#1
Quote:vESPrino v1.16 build20170103
IP address: 0.0.0.0
Chip ID: 147EA7
ready >
WebSocketSer]
[ver
PowerManager
GPIO
crc40prop_list
prop_list
---vESPrinoCFG_start---
cubic.co2.missing=missing
ds18b20.port=missing
rf.CO2=136
rf.PM25=137
rf.PM10=138
rf.TEMP=140
rf.HUM=141
rf.PRES=142
rf.GEN=143
blynk.enabled=true
blynk.auth=6513567cc86443bc8b2d1c4b6c83310b
blynk.cfg=V0,CO2,V1,,V2,,V3,,V4,,V5,,V6,,V7,
send.interval=120
wifi.ssid=Aika_Chris
wifi.p1=GEHEIM Wink
mqtt.server=192.168.44.21
mqtt.port=1883
mqtt.user=pi
mqtt.pass=Geheim Wink
mqtt_msg_arr0=co2:%CO2%
custom_url_arr0=#http://api.thingspeak.com/update?key=Geheim&field1=%CO2%&field2=%TEMP%&field3=%HUM%&field4=%PRES%
tsKey=Geheim
---vESPrinoCFG_end---
ready >
Servo
Annemometer
TimerManager

--- Setup SENSORS ---
CO2
TEST
SI7021
BME280
BMP085
PM2005
CDM7160
DS18B20
TSL2561
BH175]
[0
APDS9960

--- Setup DESTINATIONS ---
CustomHTTP
SerialDump
MQTT
RFX10]
[Blynk]
[Heap At setup end: 34424
------State changed to: 6

Waiting for WiFi]
[.]
[------State changed to: 3
IP address: 192.168.44.27 in 6567 ms
GOT IP
.
[6601] 
    ___  __          __
   / _ )/ /_ _____  / /__
  / _  / / // / _ \/  '_/
 /____/_/\_, /_//_/_/\_\
        /___/ v0.4.1 on NodeMCU

[6663] Connecting to blynk-cloud.com:8442
sendNowCond]
[--- DestHanlder: sendValue --- 1
CustomHTTPDest::process
Response Code: -13
ready >
[7072] Ready (ping: 243ms).]
[sendNowCond]
[--- DestHanlder: sendValue --- 0
ready >]
[sendNowCond]
[--- DestHanlder: sendValue --- 0
ready >]

I am not getting anymore values to thingspeak or my MQTT server. Its a bit weird. LED light is Lila. MQTT always shows me a client got connected the same second I press the Test button and directly after that a client disconected but no message is send, also my other devices work fine. Blynk and thingspeak are the same. In Blynk it appears as Online but yeah no values at all.
Reply
#2
hmmm
can you send command
prop_set "cubic.co2.missing","present"

the autodetection of the CM1102 sensor apparently failed for some reason
i need to check

you had the version with CM1102  only right ?
Reply
#3
CM1102 only thats right!

I copied the command and got the following output after doing it without the "":

Quote:[crc63prop_set cubic.co2.missing,present
prop_set cubic.co2.missing,present

Exception (28):
epc1=0x4021c6a5 epc2=0x00000000 epc3=0x00000000 excvaddr=0x00000000 depc=0x00000000

ctx: cont 
sp: 3fff1450 end: 3fff17e0 offset: 01a0

>>>stack>>>
3fff15f0:  40000f83 00000030 00000017 ffffffff  
3fff1600:  40000ea3 00000023 00000001 00000001  
3fff1610:  3fffdab0 00000000 3fffd9d0 3fff3524  
3fff1620:  3fff03c8 00000006 000000c8 40223d7b  
3fff1630:  00000000 3fff03c8 3ffefe10 00000030  
3fff1640:  3fff1978 000003c7 000003c7 4010020c  
3fff1650:  00000000 3ffe96c8 00000001 3fff1978  
3fff1660:  00000030 3fff3b6c 00000000 4010053d  
3fff1670:  4023956a 00000302 3ffefcdc 40239581  
3fff1680:  3fff4174 3fff3858 00000006 3fff2a64  
3fff1690:  00000030 3fff3b6c 3fff3b6c 40202468  
3fff16a0:  3fff3b39 00000022 3fff3b6c 3fff1978  
3fff16b0:  00000010 3fff1740 00000000 4010053d  
3fff16c0:  3fff03c8 00000063 3fff3b6c 40202ff8  
3fff16d0:  3fff3b39 00000001 3ffe9315 3fff3524  
3fff16e0:  00000010 3fff1740 3fff1740 40202468  
3fff16f0:  4025e1dc 00000008 3fff1740 402024b7  
3fff1700:  3fff1978 00000302 00000302 4010020c  
3fff1710:  3fff03c8 00000006 3fff1740 40100688  
3fff1720:  3ffe9450 00000006 3fff174c 40202408  
3fff1730:  3fff3b7c 3fff3b6c 3fff3bcc 4021be3d  
3fff1740:  00000000 00000000 00000000 3fff3b34  
3fff1750:  0000000f 00000008 40203188 4021c35b  
3fff1760:  3fff3b7c 3fff03c8 3fff0590 00000001  
3fff1770:  3fff3b6c 3fff03c8 3fff04c8 4021c13c  
3fff1780:  3fff0590 3fff07ac 3fff3754 3fff07ac  
3fff1790:  3fffdad0 00000000 3fff03c8 3fff07ac  
3fff17a0:  3fffdad0 00000000 3fff03c8 4021c190  
3fff17b0:  3fffdad0 00000000 3fff03c8 40228e07  
3fff17c0:  3fffdad0 00000000 3fff07a4 402031d4  
3fff17d0:  feefeffe feefeffe 3fff07c0 402057d0  
<<<stack<<<
?x†¬ýõ) /]
[„•…ÁHeap at start: 37744]
[vESPrino v1.16 build20170103
IP address: 0.0.0.0
Chip ID: 147EA7
ready >
Waiting for auto-connect
No I2C Devices found


Would be nice to have a FAQ or a documentation for that, where all the possible commands are listed and some workarounds how-to etc. But maybe I missed it somewhere, didn´t check the whole github etc.
But you´re answering pretty fast, thanks for that!

Greetings,
Chris from Germany
Reply
#4
in fact i have added it pretty recently Smile
i was trying to optimize startup time, and detecting the CM1102 on devices that do not have it takes 1-2 seconds. but apparently this property sometimes gets set incorrectly

can you send it but with the quotes
there is almost no proofing for errors in the firmware, so if you send a wrong command it will simply reboot Smile
in the last weeks i've improved the config tool quite a bit, so now for most of the commands there is some ui component to click.. but i haven't yet uploaded it
Reply
#5
Oh okay, that's nice to hear, great Config tool nd documentation is always for the good!

I already did it with the quotes but it seemed there wasnt much of a reaction. Is it supposed to fix my problem? Thought it only outputs debug information.Which is why I thought it worked without quotesˆˆ Thats great! than I will have a look again if it works, soon as I get from work.
Reply
#6
ahh... sorry Smile forgot to tell you then afterwards you need to reboot the device
then while restarting, when it dumps "CO2"it should then say if it found something
if it doesn't - then prehaps something else went wrong
you can also set this property to
"present"
then it will always search for the sensor
Reply
#7
ready >]
[crc63prop_set "cubic.co2.missing","present"
prop_set "cubic.co2.missing","present"]
[ready >]




ready >]
[crc56!restart
restart]
[?„܆…äÿDÈ!ü]
[„•…ÁHeap at start: 37744]
[vESPrino v1.16 build20170103
IP address: 0.0.0.0
Chip ID: 147EA7
ready >
Waiting for auto-connect]
[No I2C Devices found

--- Setup PLUGINS ---
Neopixel
c]
[rc61nop 0
nop 0
ready >
DweetIO]
[crc0Einfo
info

vESPrino v1.16 build20170103
IP address: 0.0.0.0
Chip ID: 147EA7
ready >
WebServer
crc40prop_list
prop_list
---vESPrinoCFG_start---
ds18b20.port=missing
rf.CO2=136
rf.PM25=137
rf.PM10=138
rf.TEMP=140
rf.HUM=141
rf.PRES=142
rf.GEN=143
blynk.enabled=true
blynk.auth=
blynk.cfg=V0,CO2,V1,,V2,,V3,,V4,,V5,,V6,,V7,
send.interval=120
wifi.ssid=Aika_Chris
wifi.p1=
mqtt.server=192.168.44.21
mqtt.port=1883
mqtt.user=pi
mqtt.pass=
mqtt_msg_arr0=co2:%CO2%
custom_url_arr0=#http://api.thingspeak.com/update?key=&field1=%CO2%&field2=%TEMP%&field3=%HUM%&field4=%PRES%
tsKey=
cubic.co2.missing=present
---vESPrinoCFG_end---
ready >
WebSocketServer
PowerManager
GPIO
Servo]
[Annemometer
TimerManager

--- Setup SENSORS ---
CO2]
[TEST
SI7021
BME280
BMP085
PM2005
CDM7160
DS18B20
TSL2561
BH175]
[0
APDS9960

--- Setup DESTINATIONS ---
CustomHTTP
SerialDump
MQTT
RFX10]
[Blynk]
[Heap At setup end: 34424
------State changed to: 3
IP address: 192.168.44.27 in 9755 ms
GOT IP
[9813]
___ __ __
/ _ )/ /_ _____ / /__
/ _ / / // / _ \/ '_/
/____/_/\_, /_//_/_/\_\
/___/ v0.4.1 on NodeMCU

[9847] Connecting to blynk-cloud.com:8442
sendNowCond]
[--- DestHanlder: sendValue ---]
[1
CustomHTTPDest::process
Response Code: -13
ready >
[10257] Ready (ping: 287ms).]
Reply
#8
can you enable debug (from settings)

Then in the section
--- Setup SENSORS ---
CO2
TEST
SI7021

there should be a bit more details, how the device tries to connect to the sensor
Reply
#9
I am getting this Sad

--- Setup SENSORS ---
CO2]
[Trying : 13,12
Getting CO2 Sensor Software Version]
[10,FE,FE,3F,A8,FD,FE,3F,84,2C,FF,3F,2E,54,20,40,14,93,FE,3F,A8,FD,FE,3F,
Trying : 12,13
Getting CO2 Sensor Software Version]
[10,FE,FE,3F,AA,FD,FE,3F,84,2C,FF,3F,2E,54,20,40,14,93,FE,3F,AA,FD,FE,3F,
Trying : 14,5
Getting]
[CO2 Sensor Software Version]
[10,FE,FE,3F,AC,FD,FE,3F,84,2C,FF,3F,2E,54,20,40,14,93,FE,3F,AC,FD,FE,3F,
Trying : 5,14
Getting]
[CO2 Sensor Software Version]
[10,FE,FE,3F,AE,FD,FE,3F,84,2C,FF,3F,2E,54,20,40,14,93,FE,3F,AE,FD,FE,3F,
+]
[Trying : 13,12
Getting CO2 Sensor Software Version]
[10,FE,FE,3F,A8,FD,FE,3F,84,2C,FF,3F,2E,54,20,40,14,93,FE,3F,A8,FD,FE,3F,
Trying : 12,13
Gettin]
[g CO2 Sensor Software Version]
[10,FE,FE,3F,AA,FD,FE,3F,84,2C,FF,3F,2E,54,20,40,14,93,FE,3F,AA,FD,FE,3F,
Trying : 14,5
Getting CO2 Sensor Software Version]
[10,FE,FE,3F,AC,FD,FE,3F,84,2C,FF,3F,2E,54,20,40,14,93,FE,3F,AC,FD,FE,3F,
Trying : 5,14
Getting]
[CO2 Sensor Software Version]
[10,FE,FE,3F,AE,FD,FE,3F,84,2C,FF,3F,2E,54,20,40,14,93,FE,3F,AE,FD,FE,3F,
+]
[Trying : 13,12
Getting CO2 Sensor Software Version]
[10,FE,FE,3F,A8,FD,FE,3F,84,2C,FF,3F,2E,54,20,40,14,93,FE,3F,A8,FD,FE,3F,
Trying : 12,13
Getting CO2 Sensor Software Version]
[10,FE,FE,3F,AA,FD,FE,3F,84,2C,FF,3F,2E,54,20,40,14,93,FE,3F,AA,FD,FE,3F,
Trying : 14,5
Getting CO2 Sensor Software Version]
[10,FE,FE,3F,AC,FD,FE,3F,84,2C,FF,3F,2E,54,20,40,14,93,FE,3F,AC,FD,FE,3F,
Trying : 5,14
Getting]
[CO2 Sensor Software Version]
[10,FE,FE,3F,AE,FD,FE,3F,84,2C,FF,3F,2E,54,20,40,14,93,FE,3F,AE,FD,FE,3F,
+]
[ERROR: Could not locate Cubic CO2 Sensor
TEST]
[SI7021
BME280
BMP085
PM2005
CDM7160
DS18B20
DS18B20 is on: missing
TSL2561
BH1750
APDS9960
APDS9960 - init failed!
Reply
#10
sadly this looks like a hardware failure to me

it may be that some wire has disconnected
can you please open it and have a look
there are 4 wires that connect the sensor to the main board
in one of the batches i was using single core wires and then it turned out they tend to break

in any case - i will send you a replacement, but just to check what is up with this one
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)